OS Required Apple MacOS X 10.6 or later, Microsoft Windows Vista / 7 / 8, Microsoft Windows XP (32/64 bits) SP3. I only encountered some difficulty a few weeks ago when I finally decided to transfer all the NTFS data into a new exFAT external drive for peace of mind. I tried two backup apps for that (Chronosync and Get Backup Pro) and both would keep freezing halfway (unresponsive) while transferring large folders (couple hundred GBs). I figured out eventually that the apps ran into difficulty reading some random files (say 1 out of several hundred) so the entire process would stall. That'd cause Finder to hang as well, and I'd have to eventually abort, reboot my Mac and restart the process over and over.Although 10.6 “Snow Leopard” includes NTFS write support, it is disabled by default. Third-party software like Paragon’s NTFS or the free NTFS-3G driver enabled read/write support, but a native solution was more desirable. Individual files often require conversion, but what about whole disks? Apple has long supported the universal and simplistic FAT filesystem, and added read-only support for NTFS back in 2003 in OS X 10.3 “Panther”. One of the daily hassles of using Apple Macintosh computers is the incompatibilities that arise with the broad Microsoft Windows world. I basically slept with my Macbook on my bed to do that.Seagate Backup Plus Slim portable drive, Seagate Dashboard pre-loaded on drive, NTFS driver for Mac pre-loaded on drive1, 18-inch USB 3.0 cable Operating System Mac OS X 10.6 or higher, windows 7, windows 8A lot of people including you, storing important data on Seagate external hard drive instead of on your PC/Mac hard drive. The reason is perhaps that Seagate external hard drive has been well known for a long time as one of the most reliable drives for storing data.Microsoft may be fairly criticized for producing expensive, proprietary systems, but they have dome some amazing things with disks, and NTFS is arguably one of the most advanced filesystems in wide usage. Borrowing from OS/2’s HPFS and VMS’ Files-11, NTFS is a journalling filesystem with many features, including POSIX links, alternate data streams, sparse files, compression, and encryption.Although just about everything Microsoft produces is maligned by UNIX and Mac geeks, this hatred is unwarranted in the case of the many storage advances coming out of Redmond. Microsoft introduced the advanced NTFS filesystem with their Windows NT operating system in 1993. The common FAT filesystem, supported by just about every operating system, is just too basic for modern operating systems.
![]() ![]() Open the Terminal application to get command-line access. For example, my drive mounts with the name “FreeAgent GoFlex Drive” and this is what shows up on the desktop and in Frinder under “Devices”. Look in Finder to see the name of the drive. Plug in the drive and let Mac OS X mount it read-only. But mount_ntfs won’t create this mount point, so we have to do it.Here are the steps to mount an NTFS drive read/write from the command line: For example, the GoFlex drive I bought yesterday mounts as “/Volumes/FreeAgent GoFlex Drive” by default. This is where the raw partition is mapped by the disk subsystem, and where the filesystem driver will read its data.The diskutil command gives us the "Node Name", which we'll need momentarily Record the “Device Node” entry, which will look something like “/dev/disk4s1”. Use the drive name you see in Finder in place of “drive name”, and make sure to use quotation marks around it since Terminal treats un-quoted spaces as separators rather than part of the name. Type the following command in Terminal to get necessary information about the drive. If you intend to use a drive frequently, I highly recommend reformatting it with the native HFS+ filesystem since it will be fully-supported by the operating system. Make sure your mount point is deleted as well!This method is great for occasional NTFS use, which is frankly all Mac users should need. When you’re done, you can use the Finder, the hdiutil command, or just about anything else to eject the drive. Use the node name you spotted above and the mount point you just created:Sudo mount_ntfs -o rw /dev/disk?s? "/Volumes/drive name" Finally, use mount_ntfs to mount the drive read/write using the following command. Now you must create the mount point again. This allows a drive to always be mounted read/write without any hassle. This file, called “fstab” and located in “/etc”, is not present by default but will override the “read-only” flag on a per-drive basis if found. However, I recommend investing in the Paragon driver for this use case, since it’s fully-supported!Like all UNIX systems, Mac OS X uses a configuration file to determine what it should do with certain drives. It is possible to tell Mac OS X to always mount a given NTFS drive read/write using its native driver using the following commands. Maybe it’s your Boot Camp drive, or perhaps it’s a USB hard disk drive you share with a Windows-using colleague. Serial key do need for speed carbonThe Permanent Universal MethodIt is also possible to permanently modify how Mac OS X calls the mount_ntfs command to always mount every NTFS drive in read/write mode. Also, some have reported needing multiple reboots to make it work. After a reboot, Mac OS X should automatically mount any drive with that label as read/writeNote that this can also be done using the NTFS UUID of the drive, but this isn’t present on every drive to LABEL works better. Now type control-x to save and exit, type y for yes, and hit enter. Add the following line to the file (and don’t forget the quotes around the drive name if it contains spaces!) “Nano” is a command-line editing program. Mac game emulator for windows sitThis script will simply call mount_ntfs with the “-o rw” flag every time it’s used. Create a shell script called mount_ntfs using the Nano editor: Rename the mount_ntfs command to something else by typing the following:Sudo mv /sbin/mount_ntfs /sbin/mount_ntfs_orig We won’t need the drive name or Node Name since this applies to every NTFS drive. Seagate Ntfs 10.6 How To Do ThisThis is why I decided to document it here. In fact, the best method is simply to go buy a Seagate GoFlex drive and use the Paragon driver that comes with it!But hackers and geeks like me want to know how to do this. You can easily mess up your system this way, and unsupported uses of the NTFS driver might result in data loss.If you aren’t comfortable with this kind of mucking-about or intend to frequently write to NTFS drives, I highly suggest installing NTFS-3G or Paragon’s NTFS driver. Each requires superuser access and careful typing.
0 Comments
Leave a Reply. |
AuthorMisty ArchivesCategories |